Skip to main content

Digital Watch

Logo

Logo

This project implements a circuit with an output of 42 bits that drives the display of the 7-segment digits of a digital watch.

High-level description of the project​

The aim of the project is to implement a bopkit circuit that can keep track of the current time of day by incrementing counters. The output of the circuit is a 42-bit value that can be connected to a 7-segment display, which shows the current time in the format of HH:MM:SS.

To visualize the output, we use a simulated 7-segment device implemented with the OCaml Graphics library and connect it to the simulation using bopkit's external construct.

Next, we convert the circuit to C using bop2c and repeat the simulation to test the functionality of bop2c. The 7-segment display remains unchanged, but the circuit is now run by a standalone native C application.

Finally, for some added fun, we connect the bopkit digital watch to a bopboard and run a simulation where the time on the watch can be set by incrementing the hours, minutes, and seconds dynamically using the push buttons on the board.

The 7-segment digital watch display​

The 7-segment watch display is an OCaml Graphics application. It is implemented here.

It is available in the command line as:

$ bopkit digital-watch display

This opens up a OCaml Graphics window, and displays a 7-segment watch that looks like the one in the screenshot included at the top of this page (the one with the green digits).

The application expects 42 bits on stdin, and responds by a blank line on stdout (this is the protocol for an external bopkit app of that interface).

You may try to feed a few inputs to play around with it. It's possible to use 7-segment to display some letters too!

$ bopkit digital-watch display
111011011110011011000101100010111110000000 <-- to enter on stdin

The Bopkit circuit​

The watch circuit is implemented in watch.bop.

We keep all externals blocks out of this file, so it can be compiled to C and Verilog. So as to be able to regulate the frequency, the main block defined by this file takes a 1 bit input, which it ignores.

Producing the output​

Simulate for example with:

$ bopkit simu watch.bop --num-counter-cycles 3 -o
101111110111111011111101111110111111011111
101111110111111011111101111110111111011111
101111110111111011111101111110111110000110
101111110111111011111101111110111110000110
101111110111111011111101111110111110111011
101111110111111011111101111110111110111011

Connecting the output to the device​

So we can visualize the output, we connect the output of the simulation into the 7-segment display, using a unix pipe.

So the simulation goes at the expected speed of 2 cycles per second, we use the option f 2 of bopkit counter, which we use to generate the input bit, and add it to the pipe command below:

$ bopkit counter -N 1 --no-input -f 2 \
  | bopkit simu watch.bop -o \
  | bopkit digital-watch display --no-output

Putting it all together in a circuit​

Rather than using unix pipe, we can also use external blocks for all the components into a file. That's what's done in main.bop

So the simulation command for the project becomes simply:

$ bopkit simu main.bop

The C circuit​

We use bop2c to translate the circuit into a standalone C executable:

$ bopkit bop2c watch.bop > /tmp/watch.c

So we can monitor for regressions, we committed the result of this command, and check it as part of the dune runtest target. See the result in the file watch_in_c.c.

You may integrate the C file into a simulation with these commands:

$ gcc /tmp/watch.c -o /tmp/watch.out
$ bopkit counter -N 1 --ni -f 2 | /tmp/watch.out | bopkit digital-watch display --no

The digital-watch + bopboard combo​

We connect the bopkit digital watch to a bopboard in the file watch_with_bopboard.bop.

$ bopkit simu watch_with_bopboard.bop

The time on the watch can be incremented by pressing the 3 left most push buttons of the board, to increment the hours, minutes, and seconds respectively.